Looking to increase the horsepower on your Infiniti? How about adding up to 25% more HP and TQ for your Infiniti Q50 (from 2013) 2.0 T (208 HP/ 155 kW). The shown racing performance chip increases the torque available and efficiency at the given engine speed. The easy installation can be done within 15 minutes.

Therefore a higher gear can be selected, less gear-changing is necessary in general, and fuel is used more efficiently. As a result, your car’s MPG can be increased by up to +20%. Grab a performance chip for your Infiniti Q50 for around $399.00 plus free shipping!

ASIN: B0788THQ27
Manufacturer Part Number: RC-RS-105688
Tuning performance: +26 HP and +58 lb-ft
Box includes: Chip tuning module, Wiring kit, 4 fixing clips, 4 cable ties, Users manual

Looking to add an estimated horsepower gain of 14.2 HP to your Infiniti G37? Then how about adding a K&N Performance Air Intake Kit! These air intake kits are designed to improve throttle response and engine sound. The K&N air intake kits are easy to install, usually in 90 minutes or less and they replace the stock air intake system.

These performance air intake kits last up to 100,000 miles before service is required (depending on driving conditions). Grab your K&N performance air intake kit over on Amazon for around $397.99 plus shipping and handling.

Are you looking to upgrade the performance on your Infiniti Q50? How about adding a Titanium Burnt Tips Catback Exhaust for your Infiniti Q50?

The Burnt Tips Catback exhaust systems combine top quality, performance, and flexibility in styling. They are designed for the performance enthusiasts who want to change their entire exhaust piping underneath their vehicles.

They are designed primarily for cars with dual exhaust systems. These kits usually come with the muffler section, mid-pipes, resonators, and any connector pipes.

Please note that only the pipes that come after your catalytic convertor are replaced.

ASIN: B00YRVUFTO
Item Model Number: HS14IQ5GIT

The Pedal Commander installs between the accelerator pedal sensor and the control module and works by capturing the accelerator pedal signal and transforms it. Lots of manufacturers offer similar functions via standard “sports buttons“.

The Pedal Commander reduces the pedal travel necessary in order to reach a “throttle wide open” state (full throttle response). Allows the driver to exploit the full potential of the engines.

Add one to your Infiniti Q50 today and Unleash The Hidden Power of your Engine No more Response Delay!

Boost your vehicle’s horsepower, torque, throttle response and fuel economy with an advanced Innovative Performance Chip! Safely gain up to +35 HP and up to +5 MPG in fuel mileage in your vehicle by safely optimizing your air/fuel ratio and timing curve for increased efficiency! Easily installs in less than 10 minutes, with absolutely no mechanical experience required! All Innovative Performance Chips come with an installation kit, including detailed installation instructions with easy to follow step-by-step pictures!

Boost your Infiniti today! Only $69.95 at Amazon

The air filter uses a unique (patent pending) flange retention design that requires no hardware to mount the filter to the housing. This intake system utilizes a pre-oiled, large 6″ tall conical 360 degree radial flow performance air filter with 5-layers of progressive finer mesh cotton media providing maximum airflow and performance. aFe developed these housings to snap into the top of the lower half of the factory air box to provide a hassle-free installation utilizing factory mounting clips and locations.

Intake System Features:

• In-house Dyno testing resulted in max gains of 11 HP and 20 lbs. x ft. of torque
• Outflows factory intake by 31%
• Dual Vacuum Formed ABS Plastic Housings that attaches to the stock half air box
• Dual 2.75″ Mandrel-bent Wrinkle-black Powder-coated Intake tubes improves volumetric efficiency for better performance
• Dual Pro 5R oiled 5-Layer Progressively Finer Mesh Cotton Gauze Oiled Media for Maximum Performance
• Unique (Patent Pending) Air Filter Flange Retention Design
• No Cutting or Drilling on OEM Parts for Faster Installation.

A 2.75″ One-Piece Mandrel-Bent Wrinkle-Black Powder-Coated Intake Tubes directs unrestricted airflow from the massive filter to the throttle body for more horsepower and torque. All clamps, coupling, and hardware are included for hassle-free installation. This is a direct bolt-on kit that requires no cutting or drilling on OEM parts.

Note: This intake system is not CARB exempt at this time and is not legal for sale in California or use on vehicles registered with the California Department of Motor Vehicles.

Supreme quality SICKSPEED Vacuum Intake Manifold. Manifold has 6 (six) ports, and plugs. Inlet and outlet 1/2 NPT. Small 1/8 NPT. Universal fitment. Easy to tie in a boost controller and gauges. Anodized for corrosion protection.

We are always expanding so keep an eye out for more supreme quality products from Sickspeed. Grab yourself one for around $38.88 over on Amazon.com